This automated optical fiber tensile testing program is made for operator skill impartial use in creation and laboratory configurations. Two fundamental design designs enable the consumer to pick between a set up for standard linear proof testing along with additional mandrels for rotary high power testing.

The linear version is designed for creation proof screening with forces as much as 22 N. Motor-driven clamps with carefully developed rubber inserts be sure that the Fiber Coloring Machine is not really damaged in the testing process while concurrently getting rid of the requirement for an outside air provide. Degrees of pulling force, pulling velocity and hold time are automated and easily offered to the operator from the built-in LCD touchscreen display manage. Data from assessments can be stored and accessed through the Universal serial bus dock or Ethernet interface.

Mandrels the exact same design as with NYFORS’ optical fiber recoaters can be mounted on the proof tester inside the rotary higher power configuration. The fiber is wrapped around the two mandrels which assistance it using a unique clamping system. In this way much higher lots can be employed to the fiber, allowing breaking up strength tests under managed conditions.

Changeable clamp placement facilitates testing with all the greatest force amounts as well as screening of brief fiber measures. The lightweight and light bodyweight style definitely makes the instrument simple to maneuver in a laboratory atmosphere as well as incorporate in a production work table in which space reaches reasonably limited. The equipment is actually a lightweight and lightweight tool suitable for screening the strength of optical materials approximately 30 N. The machine is created to meet all sorts of applications when a power test must be carried out.

The machine was created with all the consumer in mind. The Sheathing Line is easily positioned in the guided linear clamps, and also the screening begins automatically having a “One Touch” go switch. The built-in microprocessor controls all the essential parameters like tugging force, pulling velocity and hold time. This allows for any totally managed test each time.

The equipment can be connected to an external PC, which allows access to all programmable guidelines and configurations. The machine is tailored to face-on your own use or to the integration into different subsystems. The machine comes with an substantial ability of signing and saving details including tugging force, pulling speed and fiber diameter along with other guidelines.

Two recoat injector designs can be found. The PTR307 utilizes a computerized water pump to inject the recoat material. The volume of materials dispensed by the automated injector is managed by hand via the top-installed “Inject” switch or programmed into the device using the tablet controller. The PTR307B includes a manual recoat injection program that will require the user to personally distribute the recoat material to the mold cavity; another one injector for the PTR307B recoater can be obtained below. Make sure you note the automatic injector is only suitable for higher-index recoat material, as the handbook injector works with both reduced- and high- index recoat material; both of them are marketed separately listed below. Make sure you contact Technology Support for more information.

he manual injector can be mounted to suitable Sheathing Line via the 4-40 anchoring screws on the recoater housing (see picture for the right). Make use of a 3/32″ hex key to safe the injector prior to use. To connect the PTRRRM to the recoater mold, tighten up the connector after the eco-friendly plastic tubing, then release by way of a 1/4 consider enable rotation.

The injector is equipped with a distribution device and two-position selection handle for directing the flow of recoat material. A knurled dispensing attach with an internal plunger behaves as a syringe for that recoat material. To fill up the syringe, point the handle downwards (i.e., toward the recoat container), then spin the knurled dispensing attach counterclockwise until it rotates freely to fill up the syringe (demonstrated inside the picture to the right). Then, to inject the recoat material into the mold, point the handle horizontally (i.e., facing the knurled screw) and spin the screw clockwise till nearby the end from the journey range is achieved. Avoid bottoming out iuwekk dispenser since this may harm the interior plunger; also be careful when re-interesting the threads to avoid cross threading the dispensing screw. A number of fill up/inject steps may be needed until air is displaced in the program. Use lens tissue and an acetone or alcohol cleansing solution to gather any excess recoat material that runs from the mold.

Fiber Drawing Machine – Look At This Article..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.